Operate / Decoders
Utility and IoT
Notes for Pagers, DTMF, End-of-Train, ISM sensors, Wireless M-Bus, LoRa, Drone Remote ID, BLE, 2.4 GHz survey, Wi-Fi occupancy, RF test tools, and GNSS lab.
On this page
Pager text
German POCSAG umlauts ({ | } [ \ ] ~) convert automatically inside lowercase words (M}nchen → München, leaving [ALARM] / ALL-CAPS intact). Alpha only drops numeric/tone pages.
- Swissphone IDEA: enter RIC message keys and PSW900 organisation code in POCSAG settings. Host clock (or recording capture time) must be within the transmission’s local hour.
DTMF
Timing Q.24 (≥ 40 ms) or Fast (20 ms). Gap sets silence ending a digit sequence.
End-of-Train
Railroad telemetry: 457.9375 MHz (rear unit), 452.9375 MHz (locomotive), AU 477.7 MHz, NZ 450.2625 MHz. BCH-checked.
ISM sensors
240 kHz channel decoding OOK/FSK sensors on 315, 345, 433.92, 868, and 915 MHz (2 s deduplication; Unknown logs repeating unrecognized pulses):
- Supported: Acurite (Tower, 5n1, 606TX, 609TXC), LaCrosse (TX141/TH, TX29IT, TX35DTH-IT), Fine Offset / Ambient Weather (WH2/5/x080/24/65B/31E/31B/40, F007TH), Oregon Scientific (THGR122N/228N/968, THN132N, WGR800, THGR810), Bresser (5in1, 6in1), Nexus, Prologue, Rubicson, Alecto V1, ThermoPro TP12, Schrader TPMS, Honeywell/2GIG, Kerui, PT2262.
Wireless M-Bus
EN 13757-4 meters: modes T/C on 868.95 MHz, mode S on 868.3 MHz (own-modulator tested). Add meter ID + AES key under Keys for OMS mode 5 and Kamstrup ELL decryption.
LoRa
Decodes LoRaWAN, Meshtastic, and MeshCore (locks up to BW/3 off centre). Pick a Preset or set BW (7.8–500 kHz), SF (single or All SF7–12), IQ (Inverted for LoRaWAN downlinks, Both), Protocol, and Implicit header fields.
- Meshtastic default preset keys and MeshCore Public are built in. Add custom Keys for Meshtastic (name + base64 PSK), MeshCore (name + secret;
#tagneeds none), LoRaWAN ABP (DevAddr/NwkSKey/AppSKey), or OTAA (AppKey). - Positions plot on Map; E2E DMs flag as encrypted.
Drone Remote ID
ASTM F3411, EN 4709-002, French beacons, and DJI DroneID (needs 2.4 GHz radio: HackRF/SDRplay/Pluto, not RTL-SDR). Templates: Drone Remote ID and Drone Remote ID · Wi-Fi.
| Link | Tune | Rate |
|---|---|---|
| Bluetooth | 2402, 2426, or 2480 MHz | 4 MS/s |
| BT band | 2.4 GHz (covers ~8 of 37 long-range data channels) | 20 MS/s |
| Wi-Fi (802.11b/g) | Channel centre (e.g. ch 6 = 2437 MHz, or 2412/2462/5745) | 20 MS/s |
BLE advertisements
Lists devices, vendors, beacons (iBeacon, AltBeacon, Eddystone, Find My, Fast Pair, Exposure Notification), and scan/connect requests. Channel (4 MS/s on 2402/2426/2480 MHz) or Band (20 MS/s including long-range data). Template: BLE devices.
2.4 GHz survey and Wi-Fi occupancy
1 Hz energy monitors (no packet decoding; Span 20/40/80 MS/s; Margin over noise floor):
- 2.4 GHz survey: classifies bursts into Wi-Fi, Bluetooth, 802.15.4, microwave oven, narrowband, wideband, and continuous.
- Wi-Fi occupancy: busy %, level, and noise floor per 20 MHz channel on 2.4, 5, and 6 GHz.
Noise figure, PER tester and SID monitor
- Noise figure: Y-factor (400 kHz avg, LO excluded). Set ENR, fix gain, toggle calibrated noise source ≥ 0.5 s per state.
- PER tester: numbered 2-FSK frames (32b preamble,
1ACFFC1D, 32b seq, PRBS9, CRC-16/CCITT); reports missed, rejected, BER, restarts. Signal generator transmits matching frames. - SID monitor: tracks VLF 16–46 kHz (42 kHz span); flags > Threshold shift from 30-min baseline lasting 30 s.
GNSS lab
Tune 1575.42 MHz at 2.048 MS/s with an active GPS antenna (enable bias tee). Tracks up to 12 of 32 PRNs; cold 3D fix takes 30–50 s with 4 satellites and plots on Map at 1 Hz with PDOP.