SDRmm

Radios

USB radios

Driver requirements, quirks, and platform setup for USB and Ethernet SDRs.

On this page

See Supported radios for specs, charts, and sdrmm --doctor.

RTL-SDR

Built-in driver supports R820T / R828D tuners only (E4000, FC0012/13, FC2580 refused). Rates: 225–300 kHz or 900 kHz–3.2 MHz; BW: 290 kHz–8 MHz. Direct sampling (off/i/q) is hidden on Blog V4 / V4 Lite (built-in HF upconverter). Windows needs WinUSB via Zadig.

Serials

Many dongles ship with 00000001. SDRmm prompts once to write a unique serial to EEPROM (close the dongle, write, replug) so settings and calibration stick across USB ports. Clones without EEPROM cannot persist a serial.

KrakenSDR

Five shared-clock tuners (KrakenSDR <hub> lane 1–5; KerberosSDR has four), max 2.56 MS/s, no vendor Pi image needed. Wire all lanes into one Array in antenna order (tier locks to Shared clock).

  • Lane 1 controls the noise source and all five bias tees, so it must stay open and wired.
  • Calibration: Array triggers the noise source on retune/gain change and every minute (antennas disconnect and processors pause). Gain steps shift phase up to ~10°.
  • Errors: Noise clips, lower gain (> 75% clipped); Noise needs all lanes (incomplete bank). Check Coherent banks in sdrmm --doctor.

Tested on hardware provided by KrakenRF.

HackRF

Built-in. LNA (8 dB steps), VGA (2 dB steps), +14 dB Amp (shared RX/TX), baseband BW, Bias tee. Give 20 MS/s its own USB 2 bus to avoid silent drops.

Airspy

Built-in (omit airspy/airspyhf features to force SoapySDR).

  • R2 / Mini: 24 MHz–1.8 GHz; LNA/Mixer/VGA in firmware steps; AGC on LNA, mixer, or both; bias tee.
  • HF+ / Discovery: 1 kHz–31 MHz & 60–260 MHz; Amp (+6 dB), Attenuator (6 dB steps to -48 dB), low/high AGC, factory PPM init. Centres below 180 kHz (84 kHz narrow) clamp to that floor while still covering lower signals.

Tested on hardware provided by Airspy.

FUNcube Dongle Pro+

Built-in, fixed 192 kS/s. LNA/Mixer toggles, IF gain 0–59 dB (overload above ~25 dB with LNA+Mixer on), IF BW 200 kHz–8 MHz, RF filter, bias tee, PPM.

OS setup (Linux udev, Windows Zadig, macOS Microphone permission)
  • Linux: detaches sound/HID drivers over raw USB. Add udev rule: SUBSYSTEM=="usb", ATTRS{idVendor}=="04d8", ATTRS{idProduct}=="fb31", MODE="0660", GROUP="plugdev"
  • Windows: in Zadig, enable List All Devices, disable Ignore Hubs or Composite Parents, pick FUNcube Dongle V2.0 (Composite Parent), install WinUSB.
  • macOS: streams via Core Audio. Allow Microphone for SDRmm (or terminal) in System Settings, or samples read as silence.

Tested on hardware provided by FUNcube Dongle.

ESP-SDR

Receives via ESP32 Wi-Fi radio flashed with ESP-SDR (browser flasher). Reliable on 2.4 GHz (5 GHz on C5); 80/40/16 MS/s, 8 or 10 bits.

  • Serial: captures bursts (4096 samples default, ~0.1 s gap at 921.6 kBd). Auto-probes 2 MBd, 1 MBd, 921.6 kBd (CP2102 needs CONFIG_ESP_SDR_UART_BAUD=921600). Linux requires dialout group.
  • Ethernet (ESP32-S31 esp32s31-stream): gapless 4–40 MS/s at 8 bits (2150–2800 MHz); add via Network → ESP-SDR (Gigabit needed for 40 MS/s).

AntSDR

Talks directly to Pluto firmware iiod (no libiio; UHD images unsupported, and e310v2 does not run on E310). E310 RX1/RX2 share one synthesizer (phase coherent) and lock antenna/TX ports in firmware. Auto-discovers ant.local / 192.168.1.10. USB works out of the box (Windows needs PlutoSDR drivers).

Direct Ethernet setup and faster UDP streaming (sdrmm-iqlinkd)

Direct Ethernet: board defaults to 192.168.1.10. Assign your Ethernet port static IPv4 192.168.1.100/24 with no gateway (so internet stays on Wi-Fi). On Linux:

nmcli connection add type ethernet ifname <port> con-name antsdr ipv4.method manual ipv4.addresses 192.168.1.100/24

For router LANs outside 192.168.1.x, connect over USB and edit ipaddr_eth/netmask_eth in config.txt (SSH login: root / analog).

Faster UDP (sdrmm-iqlinkd, ~20 MS/s vs ~15 MS/s iiod): auto-detected on UDP port 30432:

rustup target add armv7-unknown-linux-musleabihf
cargo build --release --target armv7-unknown-linux-musleabihf -p sdrmm-iqlinkd
scp -O target/armv7-unknown-linux-musleabihf/release/sdrmm-iqlinkd root@192.168.1.10:/mnt/jffs2/
ssh root@192.168.1.10 'echo "/mnt/jffs2/sdrmm-iqlinkd > /tmp/iqlinkd.log 2>&1 &" > /mnt/jffs2/autorun.sh; reboot'

Tested on hardware provided by MicroPhase.

PlutoSDR and other AD936x boards

Direct iiod over USB or Ethernet (auto-discovers pluto.local, 192.168.2.1, ant.local, 192.168.1.10). Rates ~260 kS/s–61.44 MS/s (FPGA decimates below 2.08 MS/s); 2×2 boards are phase coherent.

  • 8 fast-lock profiles cut repeat retunes from ~10 ms to ~2 ms; TX synth sleeps when idle.
  • Extra chips expose per-lane AGC thresholds, quadrature/DC tracking, dual DDS TX Tone, chip state/calibration, external LO, and 1 Hz temperature/RSSI.
  • Linux requires libiio udev rules (sdrmm --doctor checks them).

SDRplay

Install SDRplay API 3.15+ and run sdrplay_apiService (no SoapySDR needed; no vendor code bundled). RF (LNA) and IF (0–39 dB) sliders both increase gain upward; AGC runs IF at 5/50/100 Hz.

  • RSPduo: Tuner 1, Tuner 2, Dual Tuner (≤ 2 MS/s each), Master, and Slave appear as separate entries (busy modes hidden).
  • Containers: see Docker SDRplay. Remote RSPs: see SDRconnect.

Aaronia SPECTRAN V6

Supports SPECTRAN V6 PLUS and SPECTRAN V6 ECO via RTSA-Suite PRO (Windows/Linux only; close RTSA-Suite before opening in SDRmm; run setup_udev.sh on Linux). Set SDRMM_AARONIA_DIR for custom paths.

  • V6 PLUS: selectable Rx1 / Rx2 inputs, host-chosen receiver clocks up to 491.52 MS/s (80–245 MHz RTBW per model).
  • V6 ECO: fixed 61.44 MS/s clock (40 MHz RTBW), single RX input.
  • GAIN is inverted reference level (20 dB = -20 dBm full scale). Sample rate is 1.5 × span (two-thirds clean); TX is half-duplex (0 dBm full scale before TX gain).

Dragon Labs CR-8

8 phase-coherent lanes (iq1–iq8), 24 MHz–1.766 GHz, fixed 12.5 MS/s, internal/external clock. Excluded from packaged builds: compile with --features cr8, install the vendor SDK (override path with SDRMM_DLCR_LIBRARY), and verify via sdrmm --doctor.

SoapySDR

Covers bladeRF (SoapyBladeRF), LimeSDR (SoapyLMS7), USRP (SoapyUHD), and remote servers (SoapyRemote). Loads at runtime (0.8 or 0.9); built-in drivers take precedence. Probed out-of-process for crash isolation (SDRMM_SOAPY_PROBE=in-process for debugging).

Install commands and custom library environment variables
System Core Example module
Debian / Ubuntu / RPi OS sudo apt install libsoapysdr0.8 soapysdr-module-bladerf
Fedora sudo dnf install SoapySDR soapy-uhd
Arch sudo pacman -S soapysdr soapybladerf
macOS brew install soapysdr pothosware/pothos/soapybladerf
Windows PothosSDR Included
NixOS soapyPlugins Included via override

Custom paths: SDRMM_SOAPY_LIBRARY, SOAPY_SDR_ROOT, SOAPY_SDR_PLUGIN_PATH. Check detection with SoapySDRUtil --find.

Edit this page on GitHub

Esc